rpm7137-r series photo link module rev.b 1/7 ir receiver module rpm7137-r series rpm7137-r series are remote control receiver modules. small-sized, light-weight, and low current consumption modules have been achieved by using resin mold. z center frequency 36.7khz z applications all household electric appliances such as tv, dvd, air conditioner and audio equipment. z features 1) low current consumption. (0.95ma typ.) 2) high ripple rejection. 3) 5 types of holders available for each set. z rpm7137-r series with holders ? under development straight type rsip-a3 l forming rsip-a3 v4 side view rsip-a3 (h13) rpm7137-r rpm7137-v4r 4.8mm ? rpm7137-h13r 15.0mm top view rsip-a3 (h4) RPM7137-H4R 15.9mm top view rsip-a3 (h8) rpm7137-h8r 7.2mm top view rsip-a3 (h9) rpm7137-h9r 12.0mm side view rsip-a3 (h5) rpm7137-h5r 9.6mm 5.5mm height to lens products no. z absolute maximum ratings (ta = 25 c) parameter symbol limits unit supply voltage v cc 6.3 10 to + 75 30 to + 100 v ma 2.0 operating temperature storage temperature output current topr tstg io c c z recommended operating conditions (ta = 25 c) parameter symbol min. typ. max. unit supply voltage v cc 5.0 v 4.5 5.5 downloaded from: http:///
rpm7137-r series photo link module rev.b 2/7 z block diagram amp 22k comparator limiter v cc r out i / v bpf detector z terminal description pin name pin no. function 1r out output terminalground power supply 23 gnd v cc z electrical, optical characteristics (unless otherwise noted, ta = 25 c v cc =5v) ? 1 600/600 s burst wave is transmitted by standard transmitter. however, it must be measured after the initial transmission pulse is 10 pulse. ? 2 it is an angle when the linear arrival distance become half. parameter symbol min. typ. max. unit conditions consumption current i cc v h l v l t on t off fo 0.95 ma no outside light, no signal input outer light condition ee < 10 (ix) isink 200 a effective distancehigh level output voltage low level output voltage on pulse width off pulse width center frequency vertical half angle 15 600 1.5 m v v s 0.5 800 horizontal half angle 1/2 1/2 600 36.7 ? 1 ? 1 ? 1 outer light condition ee < 10 (ix) ? 1 outer light condition ee < 10 (ix) ? 1 ? 2 ? 2 8 400 4.5 400 35 45 s 800 khz deg deg = < z measurement conditions (1) transmit signal 600 s 600 s fig.1 transmit signal carrier frequency=fo, duty=50% downloaded from: http:///
rpm7137-r series photo link module rev.b 3/7 (2) standard transmitter fig.2 measurement of standard transmitter proofreading standard transmitter r 20cm io=v out / r peak=940nm ? =40nm rpm-302b v out when standard transmitter output the signal at fig.1 standard photodiode output become io=5 ap-p under the measurement condition fig.2. (the radiant intensity of st andard transmitter : 50mw / sr) rpm-302b : standard photodiode has short current isc=27 a at e=1000(lx) (using cie standard light source a) (3) measurement effective distance, horizontal & vertical half angle fig.3 measurement condition for effective distance rpm7137-r series light detector faceilluminance : ee effective distance : l ( ; indicates horizontal and vertical directions) ? standard transmitter effective distance l : effective distance at =0 fig.3 horizontal & vertical half angle : the angle which effective distance became 50% of l. downloaded from: http:///
rpm7137-r series photo link module rev.b 4/7 (4) output signal 600 s t on t off v cc gnd 1/2 v cc v h v l 600 s fig.4 carrier frequency=f 0 carrier duty=50% transmit signaloutput signal (5) measurement circuit for the output voltage and the consumption current fig.5 v cc v h , v l v cc i cc r out gnd a v rpm7137-r downloaded from: http:///
rpm7137-r series photo link module rev.b 5/7 z how to use the receiver without holder please use the receiver with shield case or shield plate as an emi noise measures. (shield case and shield plate are required to be grounded.) because internal or external noise (crt, fluorescent tube, motor, lcd backlight) of the receiver ma y cause malfunction like a reduced effective distance. (in the case of internal and external noise are strong, please use rpm7137-hxr series wit h holder.) z notes (1) all characteristics of the receiver in this specification are specified by supplying burst wave fo rm (fig.1) with rohm standard transmit ter (fig.2 ). if in case of other burst wave form will be used, please check these spec. carefully under the evaluatio ns. (2) when the receiver will be used as the wire-less remote controller, please use the signal method the signal format which refer to measures to prevent malfunctioning of ir remote-controlled electric home appliances. (p ublished july 1987 by association of electric home appliances) if using other signal method, signal format, (ex: signal format which not including the le ader signal) the receiver might have chances to miss-function. (3) please set up transmitters carrie r frequency as same as the receivers f 0 frequency. otherwise error might be occurred. (4) if transmission signal has non-continues carrier, error might be occurred. continuous carrier is necessary. t1 t2 t1 t2 (5) the receiver was designed to use as in-door use only. therefore, please understand that the receiver cannot cover all characteristics, in case of using it out-door. (6) noise environment (light noise from inverter lamp, and other kind of lamps, power ri pple, electromagnetic noise from power circuit, and etc) may cause a reduced effective distance. (7) the receiver may not work properly if receiving signal judgment is done by single pulse due to the surrounding / environmental noises. to prevent such misjudgment, please make sure that the receiver is set up to work only when receiving series of coded signal. (8) emitting unit (remote control transmitter) has to be considered about its emitting device function, characteristics and characteristics of the receiver. (9) please connect holder on to the ground (gnd) of pcb. if the holder is not connected to the gnd, there i s a possibility of worsening the characteristics of product. (10) do not supply unnecessary stress to lead. (11) please pay careful attention to the lens. it might have a chance to miss-function when the lens get dust or dirty. and also please do not touch the lens. (12) in order to prevent products from esd, human body and solder iron, etc. are required to be groun ded. downloaded from: http:///
rpm7137-r series photo link module rev.b 6/7 z electrical and optical characteristics curves fig.6 bpf characteristic gain : (db) frequency : (khz) 4 3 2 1fo + 1 + 2 + 3 + 4 10.00 8.00 6.00 4.00 2.00 0.00 rerative sensitivity : (%) wave length : (nm) fig.7 optical bandwidth of the photo-diode encapsulation 700 750 800 850 900 950 1000 1050 1100 1150 1200 0 20 40 60 80 100 120 relative effective distance : (%) angle : (?) fig.8 direction characteristic (horizontal direction) 80 60 40 20 0 20 40 60 80 0 20 40 60 80 100 80 60 40 20 0 20 40 60 80 0 20 40 60 80 100 relative effective distance : (%) angle : (?) fig.9 direction characteristic (vertical direction) downloaded from: http:///
rpm7137-r series photo link module rev.b 7/7 z dimensions (unit : mm) rsip-a3 (h8) rsip-a3 rsip-a3 v4 rout pin no. gnd v cc rsip-a3 (h4) rsip-a3 (h9) rsip-a3 (h5) 3.6 1.8 7.3 2.54 2.54 15.9 4.2 2.35 1.4 1.4 0.4 0.6 0.6 0.5 12.65 7.0 2.95 0.65 6.3 1.4 4.6 1.4 2.5 0.4 1.8 9.0 12.55 3.6 2.54 2.54 2.95 1.0 6.0 0.5 0.6 0.6 7.3 3.6 0.4 4.0 0.5 1.5 2.54 2.54 9.0max. 3.2 6.0 4.8 0.8 22min. 6.5 123 6.5 2.5 3.2 6.0 4.8 0.8 2.542.54 20.0min 3 12 9.0max. 4.0 1.5 0.5 0.4 0.60 0.60 1.80 0.30 2.35 1.40 1.40 0.65 12.65 3.60 12.00 3.60 0.40 123 2.95 7.00 2.54 2.54 7.30 0.50 1.80 0.60 0.60 0.30 123 7.00 7.30 2.54 2.54 0.50 2.95 3.60 0.65 1.40 2.35 1.40 9.25 0.40 3.60 7.20 rsip-a3 (h13) 17.95 7.95 3.6 15.0 0.4 1.4 6.3 1.4 4.6 2.5 3.6 0.5 0.6 0.6 9.0 2.54 2.54 1.8 6.0 7.3 downloaded from: http:///
appendix appendix1-rev1.1 the products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. notes no technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of rohm co.,ltd. the contents described herein are subject to change without notice. the specifications for the product described in this document are for reference only. upon actual use, therefore, please request that specifications to be separately delivered. application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. rohm co.,ltd. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by rohm co., ltd. is granted to any such buyer. products listed in this document are no antiradiation design. about export control order in japan products described herein are the objects of controlled goods in annex 1 (item 16) of export trade control order in japan. in case of export from japan, please confirm if it applies to "objective" criteria or an "informed" (by miti clause) on the basis of "catch all controls for non-proliferation of weapons of mass destruction. downloaded from: http:///
|
